How to Turn an Unused Coffee Table and Old Window into a Coffee Table Display Case

My niece Elizabeth asked me to rework an unused coffee table for her, affixing an old window to its top to serve as an open and shut display window.

no images were found

Her mother, my sister, had a coffee table she didn’t need anymore that I could use for the base.

Elizabeth and I based our concept of what exactly we wanted the end product to look like on images found on Pinterest.

First I concentrated on the window:

I removed what little hardware there was on the window, two handles and the top half of a locking mechanism, and saved them to use on the finished product.

no images were found

I wanted the side of the window, which would be the top side of the table, to have a flat surface. However, I still wanted it to retain that old window look. So I left the sturdy wooden grills (these divide the glass panes) on the side that would face down but decided to remove the wooden grills from the intended top side.

no images were found

I used various chiseling tools to carefully removed the putty that held in the glass.

no images were found

Once the putty was gone I was able to remove the desired wooden grill. At this stage, I also removed the glass which was far too thin and breakable to be used as a tabletop. I would replace this later on.

no images were found

Then I removed the paint using a spray-on paint remover. There were several layers of paint so I had to do this about three times.

no images were found

One edge of the window had a deep grove down the middle. I filled it in with wood and wood filler.

no images were found

I also used the wood filler on any holes and cracks in the wood.

no images were found

After a thorough and vigorous sanding process, I painted the window white. I used spray paint because I wanted a nice smooth surface without brush marks.

no images were found

Then I turned my attention to the table:

The legs of the table were removed. The table had scalloped edges along the front and side which I removed making the table rectangle the same shape as the window.

no images were found

Using 1 x 4 wood planks I created a box and attached it to the top of the table with screws.

no images were found

The wood around the edges of the base of the table was also scalloped and not flush with the upper end so I removed these. I placed 1x4s in these areas to make sure to leave the correct gap for the legs to be attached later.

no images were found

Used wood filler in any gaps in the table pieces and sanded it all down.

no images were found

I wanted a smoother, more even look so I used ¼ inch thick sheet wood on the sides. I cut the pieces to size and used wood glue and a nail gun to attach them.

no images were found

Throughout the process, I had been applying several layers of white paint to the table and its legs.

no images were found

Added some trim to the top edges and corners of the table.

no images were found

Reattached the legs and leg supports.

no images were found

Lined the inside with interlocking aromatic red cedar planks using wood glue and a nail gun.

no images were found

Bringing the window and table together:

Cleaned the hardware the best I could and reattached it to the window. I bought a new locking mechanism but just used the bottom piece since I wanted to keep the original pieces.

no images were found

Attached the window to the table with new hinges.

no images were found

I found an antique adjustable window support on eBay and attached it to the inside.

no images were found

Replaced a new type of glass at this point and decided to use plexiglass instead of glass because it comes in different thicknesses and is stronger. I bought it at Lowes. They cut it to the exact size I needed. After setting it in place I used glazier points to hold it firmly in place.

no images were found

Done!

no images were found

I’ll be honest, I didn’t do everything in the exact order I described. A lot was done by trial and error, but I enjoyed working on the coffee table and am pleased with the result. More importantly, Elizabeth loves it!

no images were found

Rebekah Plunkett

Bekah is a mail carrier who lives in Pleasant View, Tennessee. In her spare time she loves working outside, carpentry projects, jigsaw puzzles, working on toy trains, and putting together stained glass windows.

2 thoughts on “How to Turn an Unused Coffee Table and Old Window into a Coffee Table Display Case

  • July 1, 2019 at 3:25 pm
    Permalink

    Good work! And thanks for sharing with REO readers!

    Reply

Leave a Reply

Your email address will not be published.

This site uses Akismet to reduce spam. Learn how your comment data is processed.